With 3 above ground

Duas impressoras HP LaserJet 6L Uma é nova na caixa, nunca foi usada. A outra está a funcionar mas não tem toner. Atenção - esta impressora tem porta paralela, podendo ser ligada a um computador com uma porta LPT ou através de um cabo LPT/USB. Poderá ser instalada no Windows 10. No site da Microsoft está indicado como fazer a sua instalação. PROCEDURE FOR INSTALLING A HP LASERJET 6L PRINTER ON WINDOWS 10 USING A PARALLEL CABLE Between them, Microsoft and Hewlett-Packard have made installing a LaserJet 6L printer on Windows 10, using a parallel port, a bit of a treasure hunt. Windows 10 installs it using a Postscript class driver, which the 6L does not support. Using that, try to print anything from the PC, even a test page, and you get gobbledegook and waste a lot of paper. And getting the failed print document out of the print queue and the printer's memory is a further waste of time. I found that following suggestions by HP and others to use Windows Update to install a more relevant driver always failed. If you try that, your mileage may vary. But I spent a day finding a workaround which seems robust and allows other networked PCs to use the printer. Here it is: 1) Using the front panel button on your printer, print a test page. Probably at the bottom left will be a box saying something like “Enhanced HP PCL5”. If this box indicates that the printer is using PCL5 or Enhanced PCL5 then proceed with these instructions. If the printer is not using a form of PCL5, then stop here – these instructions will not apply. 2) A Windows 10 PC is very unlikely to have a parallel connection unless one has been retrofitted. If yours doesn't, install a parallel card, e.g. in a PCI Express expansion socket. 3) Once the card is installed, use Device Manager to find out which port the card is using. 4) Connect and power up the printer. 5) Reboot the PC. 6) In Printers and Scanners, remove the printer as installed by Windows. 7) Download the file upd-pcl5-x64-6.1.0.20062.exe from http://drivers.softpedia.com/get/PRINTER/HP/HP-Universal-Print-Driver-PCL5-61020062-64-bit.shtml. This file is the last version of the HP Universal Printer Driver for 64-bit PCs which supports PCL5, the printer language used by the LaserJet 6L (see https://support.hp.com/gb-en/document/c04324001 for confirmation of this). I make no warranty that Softpedia has not installed adware or anything else with this download, but I scanned the file with Avast and Malwarebytes and found nothing. I found nothing on machine-wide scans either. 8) Run the downloaded file and follow the instructions. Install the printer as a local printer on the same port as the parallel card (see step 3 above). 9) Set the printer, which will be called HP Universal Printing PCL5 (v6.1.0), as your default printer. 10) I found that Windows soon installed the printer again using the useless Postscript driver, calling it Hewlett Packard LaserJet 6L Printer. I left it there so Windows did not reinstall it on every reboot but otherwise ignored it. Just remember never to use it when you print anything or you will get a lot of junk and waste a lot of paper.

Vendo esta motherboard em perfeito estado, otima para overclock, já contém o ultimo update de bios, o preço é fixo. Em baixo vou deixar as specs do site da ASUS: CPU Intel® Socket 1155 para 2a Geração Core™ i7/Core™ i5/Core™ i3 Processadores Suporta Intel® 32 nm CPU Supports Intel® Turbo Boost Technology 2 * Suporte Intel® Turbo Boost Technology 2.0 depende do tipo de CPU. * Por favor visite www.asus.com para ver a lista completa de CPUs suportados Chipset Intel® P67(B3) Memória 4 x DIMM, Max. 32GB, DDR3 2200(O.C.)/2133(O.C.)/1866(O.C.)/1600/1333 MHz Non-ECC, Un-buffered Memória Dual Channel Arquitectura de memória Suporta Intel® Extreme Memory Profile (XMP) * According to Intel® SPEC, the Max. 32GB memory capacity can be supported with DIMMs of 8GB (or above). ASUS will update QVL once the DIMMs are available on the market. * Por favor visite www.asus.com ou no manual do utilizador a QVL (Lista de Fornecedores Qualificados) da memória. * Devido ao comportamento do CPU behavior, a memória DDR3 2200/2000/1800 MHz irá correr a DDR3 2133/1866/1600 MHz frequência por defeito. Suporte de Multi-GPU Suporta NVIDIA® 3-Way SLI™ Technology Suporta AMD CrossFireX™ Technology Slots de Expansão 4 x PCIe 2.0 x16 (x16 ou dual x8 ou x8, x16, x16) 1 x PCIe 2.0 x4 1 x PCIe 2.0 x1 Armazenamento Intel® P67(B3) chipset: *1 2 x Porta(s) SATA 6Gb/s, vermelha 4 x Porta(s) SATA 3Gb/s, cinzenta Suporta Raid 0, 1, 5, 10 Marvell® PCIe 9182 controller: *1 2 x Porta(s) SATA 6Gb/s, vermelha JMicron® JMB362 controller: 2 x Porta(s) eSATA 3Gb/s, vermelha LAN Intel®, 2 x Gigabit LAN Controller(s) Bluetooth Bluetooth V2.1+EDR RC Bluetooth On/Off Switch Áudio Realtek® ALC889 8-Channel High Definition Audio CODEC - Suporta: Jack-detection, Multi-streaming, Front Panel Jack-retasking Características áudio: - Protecção de conteúdo áudio layer em Blu Ray - Saída(s) óptica S/PDIF no painel traseiro Portas USB Intel® P67(B3) chipset: 9 x USB 2.0 port(s) (1 at back panel, preta, 8 at mid-board) NEC® USB 3.0 controller: 2 x USB 3.1 Gen 1 port(s) (2 at back panel, vermelha) NEC® USB 3.0 controller: *2 8 x USB 3.1 Gen 1 port(s) (6 at back panel, vermelha, 2 at mid-board) Características de Overclocking ROG Connect *3 RC Bluetooth *3 ROG iDirect *3 Extreme Engine Digi+: - 8 -phase CPU power design - 3 -phase Memory power design - ML Caps on CPU respectively ROG Extreme OC kit: - LN2 Mode - PCIe x16 Lane Switch - Debug LED - Q Reset ProbeIt UEFI BIOS features: - ROG BIOS Print - GPU.DIMM Post - CPU Socket Monitor iROG Extreme Tweaker Loadline Calibration USB BIOS Flashback Overclocking Protection: - COP EX (Component Overheat Protection - EX) - Voltiminder LED - ASUS C.P.R.(CPU Parameter Recall) Caraterísticas Especiais ASUS TurboV EVO: - CPU Level Up ASUS Exclusive Features: - MemOK! - Onboard Button: Power/Reset/Clr CMOS (at back IO) ASUS Quiet Thermal Solution: - ASUS Q-Fan Plus - ASUS Fan Xpert ASUS EZ DIY: - ASUS Q-Shield - ASUS O.C. Profile - ASUS CrashFree BIOS 3 - ASUS EZ Flash 2 - ASUS MyLogo 2 ASUS Q-Design: - ASUS Q-LED (CPU, DRAM, VGA, Boot Device LED) - ASUS Q-Slot - ASUS Q-DIMM - ASUS Q-Connector Portas I/O Painel Traseiro 1 x Porta(s) PS/2 combo teclado/rato 1 x eSATA 3Gb/s 2 x Porta(s) LAN (RJ45) 8 x USB 3.1 Gen 1 1 x USB 2.0 (one port can be switched to ROG Connect) 1 x Saída óptica S/PDIF 6 x Audio jack(s) 1 x Clear CMOS button(s) 1 x ROG Connect interruptor(es) On/ Off 1 x Interruptor(es) RC Bluetooth I/O Interno 1 x Conector(es) USB 3.0 suporta(m) mais 2 USB 3.0 porta(s) 4 x USB 2.0 Conector(es) suporta(m) mais 8 USB 2.0 porta(s) 4 x Conector(es) SATA 6Gb/s 4 x Conector(es) SATA 3Gb/s 1 x Conector(es) CPU Fan 3 x Conector(es) Chassis de ventoinha 1 x Conector(es) dev Power da ventoinha 3 x Conector(es) Opcional de ventoinha 1 x Saída S/PDIF header(s) 1 x Conector(es) 24-pin EATX 1 x Conector(es) 8-pin ATX 12V 1 x Conector(es) (AAFP) áudio no painel frontal 1 x Painel de Sistema 8 x Pontos de medição ProbeIt 3 x Conector(es) de sensores térmicos 1 x En/Dis-able Clr CMOS header(s) 1 x RC Bluetooth header(s) 1 x LN2 Mode header(s) 1 x Q Reset switch(es) 2 x Conector(es) EZ Plug (conector 4-pin Molex) 1 x Botão(s) Power-on 1 x Botão(s) Reset 1 x Botão(s) Go 1 x Botão(s) BIOS Switch 1 x Conector(es) ROG light Acessórios Manual do utilizador Guia de características exclusivas ROG I/O Shield 2 x SATA 3Gb/s cable(s) 2 x SATA 6Gb/s cable(s) 1 x 3-Way SLI bridge(s) 1 x SLI bridge(s) 1 x CrossFire cable(s) 1 x Q-connector(s) (2 in 1) 1 x 2-port USB 2.0 module(s) 1 x Cabo(s) ROG Connect 1 x Conjunto de cabo(s) ProbeIt 1 x Conjunto de cabo(s) para Thermal sensor 1 x Cable ties pack(s) 1 x Autocolante ROG 1 x 12 em 1 Identificador de cabo(s) ROG 1 x RC Bluetooth card(s) BIOS 32 Mb Flash ROM, EFI AMI BIOS, PnP, DMI2.0, WfM2.0, SM BIOS 2.5, ACPI2.0a Multi-Language BIOS Gestão WfM 2.0,DMI 2.0,WOL by PME,WOR by PME,PXE Disco de Suporte Drivers ASUS AI Suite II ROG CPU-Z 3DMark Vantage Kaspersky® Anti-Virus 1-year license Dimensões físicas Formato Extended ATX 12 inch x 10.6 inch (30.5 cm x 26.9 cm)

Headset Creative Sound Blaster Tactic3D Sigma, avariado, só dá som de 1 dos lados, para reparação ou peças. Specifications: Audio Drivers 50mm FullSpectrum Headset Frequency Response 20Hz ~ 20kHz Audio Technologies SBX Pro Studio Interface 3.5mm Stereo Input, USB (Via Dual Mode adapter) Supported Operating Systems Windows® XP Professional x64 Edition, Windows® XP with SP2 or higher, Windows Vista® SP1 or higher, Windows® 7, Windows® 8, Mac OS X v10.5 and above, Windows® 10 Microphone Microphone Type: Noise-canceling Condenser Detachable: Yes Frequency Response: 100Hz ~ 18kHz Impedance: Sensitivity: -41dBV/Pa

This contains an ARM1176JZFS, with floating point, running at 700Mhz, and a Videocore 4 GPU. The GPU was capable of BluRay quality playback, using H.264 at 40MBits/s. It had a fast 3D core accessed using the supplied OpenGL ES2.0 and OpenVG libraries. The board provided the following features: Composite video out 3.5mm Audio jack Ethernet jack HDMI port 2 USB ports 26 way GPIO header including 17 GPIO, 5V, 3V3 and ground pins